When I got my hands on the Beretta A400 Xtreme Plus, I was excited to test it out in the field.
However, I uncovered some issues that needed attention, and my hands-on knowledge allowed me to dig deep into the common problems.
While using this firearm, I came across several problems such as bolt issues, light striker problems, issues with the trigger, cycling problems, double feeding, and jamming. Trust me, I was just as surprised!
But don’t fret. In this article, I am going to break down these issues one by one, explaining what I found and how you might go about fixing them.
Let’s dive into the problems and solutions, and make that next day out in the field a whole lot smoother!
Table of the Problems & their Solutions
| Problems | Solutions (Follow these instructions) |
| Bolt Issue | Clean and replace any worn-out parts. |
| Light Striker Issue | Clean, lubricate, replace firing pin, and adjust settings. |
| Problems with the Trigger | Inspect, clean, lubricate, and check gas settings. |
| Cycling Issue | Check ammo, lubricate, inspect, and replace worn parts. |
| Double Feeding Problems | Use correct shell size, check parts, and handle carefully. |
| Jamming Issues | Clean thoroughly, use quality ammo, ensure magazine fit. |
Top 6 Beretta A400 Xtreme Plus Problems & their Solutions
1. Bolt Issue
Out in the field, I stumbled upon a bolt issue that had me scratching my heads. The bolt wasn’t locking back, and I could feel the improper fit between the bolt and receiver.
Now, imagine cycling rounds, expecting everything to work smoothly, and then it doesn’t lock back! Yep, that’s exactly what I faced.
I noticed that the tolerances were off, and even the smallest speck of dirt was causing problems. It became clear that something was interfering with the components, and even some parts looked worn out.
Solution
Our first move? Cleaning the components, ensuring they were dirt-free. That alone made a difference. I also looked for wear and tear, replacing parts where needed.
Trust me, these steps worked, and my bolt issue was history! Getting back to shooting was easier than I thought!
2. Light Striker Issue
Ah, the light striker issue, I remember it all too well. While out testing the Beretta A400 Xtreme Plus, I experienced this frustrating phenomenon.
I could feel that something was off with the firing pin. It was like the ignition of the primer in the cartridge just wasn’t happening correctly.
I started to suspect it might be due to a dirty firing pin or even inadequate gas pressure settings. It seemed that every little detail mattered, from the type of ammunition to even the slightest debris in the barrel.
Solution
I took the simple approach at first: clean and lubricate. Giving special care to the firing pin and spring, I even replaced them to be sure.
Then I fine-tuned the settings, matching them to the ammunition I were using. What do you know? The light strikes stopped! It turned out that a bit of attention to detail and quality ammunition was the magic fix. Problem solved!
3. Problems with the Trigger
I didn’t see this one coming. While out in the field with the Beretta A400 Xtreme Plus, I found ourselves wrestling with some trigger issues.
From feed malfunctions to jamming, and even difficulty ejecting shells, I faced it all. Whether it was a spent round refusing to be extracted or a shell getting stuck, I were puzzled and a bit annoyed.
These weren’t problems I were expecting, but I were determined to figure out what was going wrong.
Solution
First things first, I checked for any debris and inspected all the internal parts like springs and pins. Then I cleaned, lubricated, and made sure everything was working as intended.
I even took a closer look at my gas settings and the condition of specific components like extractors. No more trigger issues! It’s amazing what some maintenance and attention to detail can do.
4. Cycling Issue
Out in the field, testing the Beretta A400 Xtreme Plus, I encountered some cycling problems that caught me by surprise. I noticed jams, misfires, and even excessive cycling.
I were stumped at first but realized it might be related to the gas system of this semi-automatic shotgun.
The pressure on the short-stroke piston seemed off, and I also considered the recoil spring assembly. It was a tricky problem that messed with my shooting performance, and I knew I had to tackle it head-on.
Solution
I started by checking the ammunition types and ensuring I were using the right shells. Then came the maintenance part: proper lubrication and thorough inspection of all components.
I even disassembled the action, looking for signs of wear or damage. Replacing a few worn-out parts and reassembling everything back, I were back on track.
It took a bit of elbow grease, but the cycling issues were resolved! The gun was back to its reliable self, and I were more than satisfied with the outcome.
5. Double Feeding Problems
While out testing the Beretta A400 Xtreme Plus, I ran into a snag known as double feeding. Two shells were loading into the chamber at the same time, and boy, did that mess things up.
Firing was out of the question, and ejecting shells became a real hassle. I observed that it could have been due to using an oversized shell, mishandling during loading, or perhaps a broken part within the gun.
It was a concerning problem, and not only did it hinder my shooting, but it felt like I were stuck in a loop with no easy way out.
Solution
The solution? Well, first, I made sure to use the correct shell size and checked all the gun’s parts. Then I slowed down my loading and paid careful attention to my grip on the forearm and trigger guard. It took some patience, but I managed to get rid of the double feeding.
If none of that had worked, I were ready to head to a gunsmith, but luckily, my methodical approach did the trick. Handling the Beretta A400 Xtreme Plus carefully, I learned, was the key to keeping things smooth.
6. Jamming Issues
Jamming! If you’ve ever been out in the field with a Beretta A400 Xtreme Plus, you might’ve faced this issue.
I sure did. A shell casing would get stuck, refusing to feed into the chamber. I found obstructions, deformed casings, dirt, and even worn-out parts at the heart of the problem.
There’s nothing like being ready for a shot and having the gun jam on you. Frustration doesn’t even begin to cover the emotions I felt. It was a clear sign something was wrong, and I needed to figure it out.
Solution
Our solution was methodical. I took apart the gun, cleaned every spring and pin, and got rid of the dirt that was causing the blockages.
I also switched to high-quality ammo meant specifically for my gun model. Ensuring the magazine fit snugly made a difference too.
These steps, although simple, did wonders in banishing the jams and brought back the joy of shooting. Patience and persistence saved the day, proving that even the most vexing problems can have straightforward solutions.
Conclusion
The Beretta A400 Xtreme Plus isn’t without its challenges. my extensive field testing revealed a range of problems from bolt issues to jamming.
With some basic maintenance and attention to detail, I were able to rectify most of the issues I encountered.
It’s important to recognize that no gun is perfect, and knowing how to manage its weaknesses is part of the art and science of firearms. All things considered, the Beretta A400 Xtreme Plus stands as a high-quality, if demanding, choice for those who are serious about their shooting.
FAQs
Is the Beretta A400 reliable?
Yes, the Beretta A400 Xtreme Plus is a reliable, soft-shooting gun, delivering outstanding performance, particularly for duck hunting.
What is the difference between Beretta A400 Xtreme and A400 Xtreme Plus?
The Plus model features a bigger ejection port, an oversized bolt-handle and bolt-release latch, with just the little things changed.
How many chokes come with Beretta A400 Xtreme Plus?
The Beretta A400 Xtreme Plus comes with 5 Choke Tubes – F, IM, M, IC, C.
How many shells does a Beretta A400 Xtreme Plus hold?
The Beretta A400 Xtreme Plus holds a capacity of 3+1.
What chokes does a Beretta A400 Xtreme Plus use?
Cylinder (C), improved-cylinder (IC), modified (M), improved-modified (IM), and full (F) chokes are included.
What is the length of pull on the Beretta A400 Xtreme Plus?
The length of pull on the Beretta A400 Xtreme Plus is 14 7/16″ out of the box.
