Most Common Taurus G3C Problems And How To Fix Them

Last Update:

In my extensive field testing, I had the chance to scrutinize the Taurus G3C firearm. 

Through rigorous handling and evaluating its performance under various conditions, I’ve uncovered some inherent Taurus G3C Problems that could affect the user experience. 

Among the problems I encountered were issues with the barrel, jamming, the magazine, the gun not returning to battery, failure to extract and feed, and problems with the slide. These challenges were not minor annoyances; they pointed to deeper concerns that required proper examination.

This article will delve into these common problems and provide practical solutions based on my encounters with the Taurus G3C.

Overview of the Problems & their Solutions

Barrel ProblemsChange the barrel after proper disassembling.
Jamming IssuesOpt for quality ammunition and regular cleaning.
Magazine ProblemAccurate spring installation or replacement.
Not Returning to BatteryLubrication, polishing, and using quality cartridges.
Failure to ExtractClean the chamber, replace parts, use good ammunition.
Issues with the SlideMeasured firing, adequate lubrication.
Feeding IssuesInspect and replace the magazine, clean feed ramp, use proper ammunition.

Top 7 Taurus G3C Problems & Solutions

1. Barrel Problems

During my field tests, one of the most noticeable problems with the Taurus G3C was the failure to chamber. 

I soon realized this was a manufacturing fault, often related to the barrel. Whether it was failing to elevate the round to the chamber or issues with accuracy, it was clear that something was amiss. 

Lubrication seemed to help temporarily, but it wasn’t a lasting solution. The affected gun’s slide would move forward, but the round would still fail to chamber properly.


Through trial and error, I found that changing the barrel was the only effective solution. 

I ensured the gun was clear, removed the slide, removed the firing pin and barrel, and then inserted a new one. After reassembling, I tested the firearm, and the chamber failure issue was resolved. 

This hands-on experience gave me the confidence that changing the barrel is a practical fix for this problem.

2. Jamming Issues

Jamming became a consistent and worrying issue during my testing sessions with the Taurus G3C. Whether it was due to poor-quality ammunition or low-grade magazines, this problem created real challenges for me in the field. 

I even observed that the firearm’s overall condition, especially if not well-maintained, contributed to these malfunctions. 

This wasn’t just an inconvenience but a potential safety concern that needed to be addressed.


My hands-on experience led me to a multi-faceted approach to solving this problem. I began by opting for high-quality ammunition and magazines, which significantly reduced jamming. 

Regular cleaning of the barrel, chamber, and other components also made a big difference. For persistent issues, consulting a professional gunsmith proved beneficial, as they were able to identify and fix any underlying problems. 

Following these steps, I minimized the jamming issue and improved the firearm’s performance.

3. Magazine Problem

During my time with the Taurus G3C, I stumbled upon a particularly frustrating problem involving the magazine release button. 

This part would often detach, especially when jamming occurred. I recognized that the releasing spring breaking was behind this issue, and improper installation was a common cause. 

Whether it was a loose retaining screw or a manufacturing defect, it was an issue that needed immediate attention.


Addressing this problem required a bit of hands-on tinkering. I found that accurately installing the spring could resolve the issue if the spring was not broken. 

Checking the retaining screw was essential, and tightening it, if loose, could fix the problem. If there were cracks or other damages, I contacted professionals or the manufacturer for a replacement. 

Following these steps ensured that the magazine release functioned as intended, and the Taurus G3C became more reliable in the field.

4. Not Returning To Battery

The issue of not returning to battery was another challenge I faced with the Taurus G3C. This problem would persist across various magazines, and particular brand cartridges seemed to exacerbate it. 

Federal cartridges were especially troublesome. I even noticed an odd rustling noise from the chamber at times. 

It became clear that a manufacturing flaw, combined with other factors like the finish on the barrel or magazine issues, contributed to this persistent problem.


My field experience led me to a series of solutions. First, I tackled the manufacturing flaw with a bit of lubricant or oil, easing the friction. 

Polishing the barrel eliminated any rough finishes. Using high-quality cartridges and properly-sized ammunition provided better performance. 

Thorough cleaning of the slide and barrel and ensuring correct magazine insertion further helped. Implementing these measures made the firearm recover to full charge reliably.

5. Failure To Extract

When I were testing the firearm, the failure to extract issue was a real headache. This problem seemed to stem from various sources, such as dirt in the chamber, worn extractor springs, and damaged extractors. 

To make matters worse, using the wrong type or low-quality ammunition could also trigger this issue. The frustration was palpable, as this failure could be risky and severely hamper the firearm’s performance.


The solution I implemented required a careful and systematic approach. First, I cleaned the chamber to remove any grime. 

Next, I inspected the extractor spring and extractor, replacing worn or damaged parts. Lastly, I became meticulous about the type and quality of ammunition I used. These steps made a significant difference, improving the firearm’s performance and alleviating the failure to extract issue that had been plaguing us.

6. Issues with the Slide 

During my testing with the Taurus G3C, I encountered a peculiar issue: the slide became scorching hot when firing many magazines rapidly.

This heating not only forced me to wait between firing rounds but also seemed to negatively impact my shooting accuracy. 

I found ourselves having to slow down and take caution, which was frustrating during timed practice sessions.


I quickly learned that a measured and gentle firing approach was crucial to manage this problem. I reduced the overheating issue by pausing after firing a complete magazine and allowing the slide to cool down. 

I also made sure the firearm was adequately lubricated to minimize friction. 

Additionally, considering heat-resistant slide finishes or cooling agents might further alleviate this issue, though I didn’t test these solutions ourselves. 

This systematic approach allowed me to continue using the firearm without risking harm or sacrificing accuracy.

7. Feeding Issues

In my hands-on experience with the Taurus G3C, feeding issues cropped up a few times. These problems ranged from the magazine not being properly seated to dealing with low-quality ammunition. 

It got particularly frustrating when I discovered that even the magazine springs were wearing out, disrupting the feeding of rounds into the firearm. 

The consistency of this issue put a damper on my shooting sessions.


I tackled these feeding problems by following a systematic approach. 

First, I inspected the magazine for any wear or damage and replaced it when necessary. Next, I experimented with different ammunition brands to identify ones that worked smoothly. 

Cleaning the feed ramp became part of my routine maintenance, and finally, replacing the recoil spring with a stronger one made a significant difference. I brought the firearm back to its optimal performance by paying attention to these areas.


The Taurus G3C, despite its initial allure, revealed several issues through my hands-on field testing. The firearm’s challenges, such as jamming, barrel problems, and feeding issues, were not to be taken lightly. 

However, it’s worth noting that each problem was met with practical solutions. 

By adjusting ammunition choices, performing regular maintenance, or even replacing parts, I could enhance the performance and safety of this firearm. 

While not without its flaws, the Taurus G3C can still be a reliable choice when users are aware of its weaknesses and equipped to deal with them.


Is a Taurus G3c drop safe? 

Yes, the Taurus G3c is drop safe, as it includes both a thumb safety and a trigger safety.

How many rounds will a Taurus G3c last? 

The Taurus G3C can hold a 10+1 capacity magazine of 9mm or an extended one with 12 rounds.

Which is better: Taurus G3 or G3c? 

The G3 is better in terms of its extended rail and higher magazine capacity, while the G3c may only accept compact pistol accessories and has a lesser capacity.

Is Taurus a quality pistol? 

Yes, Taurus offers affordable, workmanlike designs known for good performance and function, mimicking proven American revolvers.

One Request?

I worked hard on this post to help the shooters community. it would help me a lot if you consider sharing it on social media network

BecauseSharing Is Caring..

Because Sharing Is Caring..

Photo of author


I'm Micheal, an avid shooter and hunting enthusiast from Texas. I'm a recreational shooter who loves to spend time at the range and enjoy learning about new firearms and gears. I love to write about guns and share my passion for shooting with others.

4 thoughts on “Most Common Taurus G3C Problems And How To Fix Them”

  1. I recently purchased a Taurus G3c 9mm pistol for concealment carry to replace my hated Ruger LC9 hammer fire, 1st edition pistol. The Taurus ergonomics fit my hand like a tailored glove, comfort of firing was great. Initially, I fired about 50 rounds plus of assorted ammunitions without any failures to feed, fire or extractions. As standard practice, after firing, I disassemble and thoroughly clean the pistol. I noticed a fair amount of wear on the outside, front of barrel area, but applied stainless barrel lube, as suggested by mfg. The second trip to the range, all, every round was light strike, non fire; yet every one of these rounds fired flawlessly in my friends Star Model 30 9mm pistol, and chronographed within 30fps per 5 rounds. I changed the striker assy. to Lakeline, same results. Now I have ordered the Glock 6lb striker spring, for repair of this common issue.

    • Thanks for sharing your Taurus G3c experience. It’s great to hear it fits your hand well! Those light strike issues are a bit tricky, aren’t they? Good call on trying the Glock 6lb striker spring. Hope it solves the problem for you. Keep me updated on how it goes

  2. I ordered Wolf /(For Glock) 6lb striker Springs,They Would Not Fit in zany G2c ! Too Big around,Diameter! Wouldn’t Work! Is The G3c Striker Tube assembly Larger in Diameter?

    • It’s tricky with aftermarket parts sometimes. To answer your question, yes, the G3c might have slight differences in internal dimensions compared to the G2c, including the striker tube assembly. It’s always best to go for parts specifically designed for your model to avoid compatibility issues.


Leave a Comment