I have taken the Beretta APX A1 Carry problems into the field to test its performance.
After spending considerable time with this firearm, I’ve understood it inside and out. My hands-on experience has been eye-opening, and I’ve identified several issues that might catch a user off guard.
These problems include not returning to battery, sight problems, trigger issues, light primer strikes, failure to fire, jamming problems and slide issues.
But don’t worry; I’m not just here to tell you about the problems; I’ll also guide you through the solutions.
Overview of the Problems & their Solutions
| Problems | Solutions |
| Not Returning To Battery | Diagnose the issue through observation, replace damaged parts such as the cocking lever, striker block lever, striker block, or striker itself. |
| Sight Problems | Remove and coat the loosening screws with Loctite, then reinsert and tighten carefully. |
| Trigger Issue | Clean the trigger assembly, consult a gunsmith if necessary, and replace specific malfunctioning parts. |
| Light Primer Strike | Experiment with different ammo, contact Beretta’s customer service if the problem persists. |
| Failure To Fire | Inspect ammunition and gun’s inner workings, replace weak springs, and seek professional assistance if needed. |
| Slide Issue | Clean slide rail, apply lubricant, replace worn-out recoil spring if needed. |
| Jamming Problems | Switch to high-quality ammo, clean the gun thoroughly, replace worn-out or faulty magazines. |
Top 7 Beretta APX A1 Carry Problems & Solutions
1. Not Returning To Battery
One of the rare but noticeable problems with the Beretta APX A1 Carry is the issue of not returning to battery.
This problem means that the slide doesn’t fully return to its forward position after firing, causing a disruption in the firing sequence. During my testing, I could feel something wasn’t right when the firearm refused to cycle properly.
The sensation of the slide jamming up was both unexpected and concerning, leading me to carefully investigate what was happening.
Solution
After diagnosing the issue, I found that it might be due to damaged internals or incorrect reassembly. My hands-on experience allowed me to try different approaches to fixing it.
I observed the internal mechanism through the ejection port by removing the recoil spring and barrel and putting the slide back on.
After pulling the trigger slowly, I pinpointed the issue to specific parts such as the cocking lever, striker block lever, striker block, or the striker itself.
Replacing the damaged parts was my tested solution, and I’m glad to report that the firearm functioned smoothly afterward. Simple observation and careful replacement got the job done, and it might work for you too!
2. Sight Problems
During my hands-on testing with the Beretta APX A1 Carry, I stumbled upon an issue that might sound minor but can have major implications: the screws on the front sights slowly loosening over time.
I first noticed something was amiss when my aim started drifting.
The problem seemed to stem from the recoil, but it wasn’t something i’d observed with other firearms. This issue made me feel uneasy, as it could affect accuracy in a critical moment.
Solution
I knew I had to address the sight problems promptly, so I carefully assessed the screws and realized that the loosening was gradual and occurred mainly due to the gun’s recoil.
Our practical solution involved using Loctite, a threadlocker designed to prevent fasteners from loosening.
After removing the screw, checking for any damage, and coating it with Loctite, I reinserted and tightened it, making sure not to over-tighten it.
I felt a sense of relief when the sight was secure again, knowing that this simple fix had rectified the issue.
3. Trigger Issue
While enjoying my time with the Beretta APX A1 Carry, I couldn’t overlook a persistent issue with the trigger. I found it to be long, heavy, and lacking a clean break.
This wasn’t just a minor inconvenience; it actually hindered my shooting experience.
The sensation of struggling with the trigger pull was far from pleasant and took a toll on my accuracy. As much as I appreciated other aspects of this firearm, the trigger problem was something that needed immediate attention.
Solution
I knew I had to dig deeper to resolve the trigger issue. my first step was unloading and disassembling the gun, allowing me a clear view of the trigger assembly.
A thorough inspection led me to discover that some parts weren’t functioning properly, and there was debris buildup inside. Cleaning the assembly with solvent and a brush solved part of the problem, but the long pull remained an issue.
It became clear that professional intervention might be necessary, and I didn’t hesitate to consult a gunsmith.
Their expertise in replacing specific parts brought the trigger back to life, making my shooting experience enjoyable once again.
4. Light Primer Strike
In my rigorous testing of the Beretta APX Carry, one of the issues I encountered was a light primer strike. This wasn’t just a one-off problem; it seemed to persist and was certainly not due to the ammunition I was using.
I felt frustrated and concerned as I worked through various shooting sessions, consistently encountering this issue.
The anticipation of a possible light primer strike started to affect my confidence in the firearm, overshadowing some of its other redeeming qualities.
Solution
Our first instinct was to experiment with different types of ammo, thinking this might be a solution. However, this approach didn’t yield any positive results. Realizing that the problem might be beyond my control, I contacted Beretta’s customer service.
Like other users, I had my firearm serviced by Beretta, which proved to be the right course of action.
The light primer strike issue was resolved, although it was eye-opening that it needed professional intervention.
5. Failure To Fire
During my time with the Beretta APX Carry, I faced a situation that left me quite uneasy – the failure to fire. It’s something that every shooter dreads and something that undermines the reliability of the firearm.
Whether it was due to improperly seated rounds, issues with the primer, or a malfunction within the firing pin or firing pin channel, this problem caused a constant sense of unpredictability.
With each pull of the trigger, the tension built, wondering if the round would go off or if I’d be faced with another failure to fire.
Solution
To get to the bottom of the problem, I first scrutinized the ammunition, ensuring compatibility and proper seating. No luck there. Then, I delved into the gun’s inner workings, inspecting the firing pin, firing pin channel, and trigger and hammer springs.
A closer look at the springs revealed a weakness that was causing the issue. A quick replacement and some careful reassembly, and the problem was resolved. This process taught me the value of a thorough inspection and knowing when to seek professional assistance.
It reminded me that understanding your firearm and regular maintenance can be the key to avoiding such frightening failures.
6. Slide Issue
Ah, the slide issue. It’s one of those nagging troubles that I stumbled upon with the Beretta APX Carry. Imagine the slide refusing to close completely, getting stuck about an eighth of an inch from being fully closed.
That’s exactly what happened. Pushing it required more effort than usual, and it felt like something was obstructing its path. This was frustrating because it made the handling of the firearm feel clumsy, and more importantly, it raised concerns about safety and reliability.
The sensation of the slide hanging up on something wasn’t just bothersome; it was alarming.
Solution
Addressing this slide issue took a bit of trial and error. I first thought it might be due to tight springs, common in newer guns, but that didn’t seem to be the culprit. A close examination revealed dirt clogging the slide rail, so I cleaned it thoroughly and applied lubricant.
No luck there, either. Finally, I noticed signs of wear on the recoil spring.
Replacing it did the trick! This problem taught me the importance of paying attention to the intricate details of the firearm and not overlooking something as essential as a worn-out spring. Sometimes, the solution is hiding in plain sight!
7. Jamming Problems
Jamming problems with the Beretta APX Carry? Oh, you bet I’ve been there. My field tests found that sometimes the gun would just refuse to cooperate.
Rounds would fail to feed, chamber, or eject, and the entire shooting experience would grind to a halt. The frustration was real; each jamming incident increased my concerns about this otherwise reliable firearm.
I needed to figure out what was causing this disturbance, whether it was the ammunition, firearm, or magazines. It was a problem that required immediate attention, as it affected my shooting experience and my trust in the firearm’s reliability.
Solution
Our initial suspicion fell on the ammunition. Switching to high-quality, clean ammo solved part of the problem.
Then, I discovered that thoroughly cleaning the gun, focusing on the barrel and chamber, made a significant difference. Finally, inspecting the magazines revealed some wear and tear contributing to the jamming.
Replacing the faulty magazines nailed it! I learned from this experience that sometimes, solving a problem requires attacking it from multiple angles.
Conclusion
Testing and reviewing the Beretta APX A1 Carry was an enlightening experience for us. It was a journey of excitement, curiosity, challenges, and learning.
The Beretta APX A1 Carry shows innovation, craftsmanship, and attention to detail. Despite some problems like not returning to battery, sight loosening, trigger issues, light primer strikes, failure to fire, slide issues, and jamming, my hands-on experience provided me with the insight to diagnose and fix them.
Some solutions were simple and within the reach of any gun owner; others required professional intervention.
Our field experience has given me a practical understanding of the Beretta APX A1 Carry, and with the solutions in hand, it’s a firearm that can be relied upon with confidence.
FAQs
Is Beretta APX reliable?
Yes, the Beretta APX A1 Full Size pistol is noted for its good ergonomics, slide serrations, grip texture, accuracy, and reliability.
Is Beretta APX better than Glock?
Beretta APX wins; for a lightweight, easy-to-conceal pistol with higher capacity, Glock 19 might be preferred.
Is the Beretta APX drop safe?
Yes, Beretta APX has a device on the trigger that prevents unintended firing, making it drop safe.
Where is the Beretta APX carry made?
The Beretta APX Carry is made in Gallatin, TN.
